Gafe dafalen dɔ min bɛ sigibaga kan ka ɲɛsin Inox frame Wall-Mount Vessel Sinks ma

Kogo-mount jisigiyɔrɔ dɛsɛ sababu kelen min ka teli ka kɛ, o tɛ jisigiyɔrɔ ye. O ye kogo ye min b’a dɛmɛ. Jagokɛminɛnw jisigiyɔrɔ min doni dafalen don - basikɛti, ji, baarakɛla jɔli girinya - bɛ fanga kɛ a kanKilo 150 yeka doni jɔlen na ani ka caya kosɛbɛ fanga fangama na. Ni kogo jɔcogo tɛ se ka o doni ta, a sigili bɛ dɛsɛ a mana kɛ cogo o cogo.

Kogow jɔli suguyaw ani doni seko

Kogo suguya	Load Capacity (ankɔri yɔrɔ kelen-kelen bɛɛ) .	Kalansenw bɛnkan
Béton/maçonnerie (solid) .	200+ kilo	Ankɔri tilennen, kɔkanna tɛ wajibiya
Bloc de béton (bɔgɔdaga) .	Kilo 80–120 ye	A bɛ epoxy-set ankɔriw wajibiya walima ka tɛmɛ-boltiw fɛ
Nɛgɛdaga + jalen	kilogaramu 30–50	A bɛ 18mm plywood kɔkanna de wajibiya studs ni ɲɔgɔn cɛ
Jiriw ka sɔgɔli + drywall	kilogaramu 60–90	A bɛ 18mm plywood kɔkanna walima cross-blocking de wajibiya
Drywall dɔrɔn (a tɛ kɛ ni stud kɔkanna ye) .	A ma jate	AW KAN’A SƆRƆ - frame ka kan ka span studs

A ka Plywood Backing Sɛgɛsɛgɛli

Ka ɲɛsin nɛgɛ-sɔgɔsɔgɔninjɛ ni yiriw-sɔgɔsɔgɔninjɛ kogow - jago jɔli suguya minnu ka ca kosɛbɛ - labɛnni wajibiyalen ye a sigili ye18mm structurel plywood panneausɔgɔsɔgɔninjɛw ni ɲɔgɔn cɛ kogo dafalen kɔfɛ. O dɛmɛ in ka kan ka:

• A bɛ kɛ ni jirisun fila ye a dɔgɔyalenba la (a ka c’a la, u bonya bɛ se milimɛtɛrɛ 800–900 ma) .
• Aw bɛ aw siri jirisun kelen-kelen bɛɛ la ni #12 jiribolo naani ye a dɔgɔyalenba la walima ni nɛgɛ juruw ye minnu bɛ aw yɛrɛ{1}}bɔgɔ sɔgɔlan kelen na
• Aw bɛ 150mm janya ka tɛmɛ frame mounting bracket senna-tɛgɛrɛ kan fan bɛɛ fɛ
• Aw bɛ a sigi ka kɛɲɛ ni jirisunw ɲɛfɛla ye sani jalen ka wuli

Sani-Installation Sɛgɛsɛgɛli Sɛgɛsɛgɛli

Sani aw ka karamɔgɔya bɔ:

• Kogo suguya dafa:Aw bɛ baara kɛ ni stud finder ye ani ka piloti dingɛ fitinin dɔ sɛgɛsɛgɛ- walasa ka stud fɛnw ni u ni ɲɔgɔn cɛ danfara sɛgɛsɛgɛ.
• Sɛgɛsɛgɛli kɛ kɔkannakow kan:Ni kogo banna kaban, aw bɛ plywood kɔkanna sɔrɔ ni stud finder ye min bilalen bɛ deep-scan mode la. A dakunw ka kan ka dɔn 150mm ka tɛmɛ a karamɔgɔya labɛncogo kan.
• Nivo lajɛ:Aw bɛ 1200mm hakili hakɛ dɔ bila ka jɔ kogo la jiginni yɔrɔ labɛnni na. Ni fɛn o fɛn bɛ tɛmɛ milimɛtɛrɛ 3 kan karamɔgɔ janya kan, o bɛ shimming walima kogo sanfɛla latilenni de wajibiya sani karamɔgɔ ka sigi.
• Aw ye plomberie rough-in dafa:Aw bɛ a lajɛ ni fɛnw dilancogo siraw bɛ bɔ kogo la karamɔgɔ ka tigɛyɔrɔ latigɛlen kɔnɔ ani ko jibɔyɔrɔ min janya ka gɛlɛn-, o ni jibɔyɔrɔ ka janfa bolo kɔrɔtalen bɛ bɛn.

2. Frame Leveling ani Hardware Anchor Sugandili

Nɛgɛ min tɛ sɔgɔ, o ye a sigicogo jɔcogo ye. A bɛ doni bɛɛ bɔ jisigiyɔrɔ la ka taa kogo la. A sigicogo tigitigi b’a jira k’a ɲɛsin a ma ni jisigiyɔrɔ sigilen bɛ yɔrɔ kelen na, ni ji bɛ bɔ ka ɲɛ, ani ni a sirilen don kosɛbɛ san tan caman kɔnɔ.

Kalansenw lajɛcogo ani a taamasiyɛnni

Jagokɛlaw fanbakogo-mount minɛnw jigincogo karamɔgɔbɛ se yɔrɔ dɔw lajɛlen na. Aw bɛ jamalajɛ dafa duguma fɔlɔ, o kɔ:

• Aw bɛ karamɔgɔ lajɛlen bila kogo la, a jiginni janya kofɔlen na. Jagokɛlaw ka ADA-sɔrɔyɔrɔw bɛ sinki rim de wajibiya at864mm (santimɛtɛrɛ 34) .sanfɛ duguma dafalen.
• Aw bɛ taamasiyɛn kɛ jiginni dingɛ yɔrɔw bɛɛ la karamɔgɔ bracket dingɛw fɛ ni kretiɛn walima cɛmancɛ punch ye.
• Aw bɛ karamɔgɔ bɔ ka a sɛgɛsɛgɛ ko taamasiɲɛ bɛɛ bɛ ɲɔgɔn na ni laser nivo walima 1200mm hakili hakɛ ye.

Ankɔri Sugandili ka kɛɲɛ ni kogo suguya ye

Ankɔri suguya bɛ dɔn kogo substrat fɛ. Baara kɛli ni ankɔri jugu ye, o bɛ sigili dɛsɛ lase - diɲɛ bɛɛ ka ankɔri tɛ yen.

Nivoya Sequence (Sɛbɛnni min bɛ kɛ ni nivoya) ye

1. Aw bɛ karamɔgɔ bila yɔrɔ la ani ka sanfɛla-siraw bɛɛ don a la ka lafiya (bolokɔni-sirilen dɔrɔn).
2. Aw bɛ hakili nivo dɔ bila karamɔgɔ ka jiginni barajuru tilennen kan. Aw bɛ karamɔgɔ jɔyɔrɔ ladilan fo bulon ka kalan kɛ cɛmancɛ salen na.
3. Aw bɛ sanfɛla-row ankɔriw siri ka50%ka laban torque (kurunba) la.
4. Aw bɛ duguma-row ankɔriw don ka lafiya.
5. Segin ka -nivo lajɛ bar horizontal kan ani ka ladilan ni mago bɛ a la.
6. Aw bɛ ankɔri bɛɛ siri ka se girinya dafalen ma cross-pattern sequence kɔnɔ.
7. Aw bɛ segin ka -nivo lajɛ siɲɛ kelen laban na sani aw ka jisigiyɔrɔ sigi.

3. Ka jibɔyɔrɔw bali minnu bɛ sɔrɔ tuma caman na

Ji tiɲɛni min bɛ bɔ kogo-mount sink sigili la min bɛ ji bɔ, o bɛ nɔ bila kogow kɔnɔna na, duguma decking, ani duguma sanfɛla sanfɛla la. Jagokɛyɔrɔw la, bɔgɔdaga kelen min ma dɔn, o ka juru musaka ka teli ka tɛmɛ fɛnw jɔli baarakɛnafolo bɛɛ kan.

Drain Assemblage (Drain Assemblage) ka sigicogo

Jibolisira jɛgɛn ye faratiba-jibɔyɔrɔ ye. Siginidenw sigicogo:

• Aw bɛ biɲɛ dɔ kɛ min bɛ to sen na100% silikoni sigilanka taa jibɔyɔrɔ flansɛ jukɔrɔ.
• Aw bɛ jibolisira flansɛ don jibolisira da la.
• Ka bɔ duguma, aw bɛ lastikuw degun gazi kɛ jibolisira farikolo kan, o kɔ aw bɛ friction washer ni lock nut kɛ.
• Bolo-aw bɛ dakun nut siri, o kɔ aw bɛ tilayɔrɔ kelen wɛrɛ siri ni jibɔlan ye.Ni -gɛlɛn ka tɛmɛ, o bɛ lastikuw gazi tiɲɛani ka bɔgɔdaga siraw Dabɔ minnu bɛ juguya ni gɛlɛya kelen-kelen bɛɛ ye ɲɔgɔn kɔ.
• Aw bɛ silikoni tɛmɛnen ko ka bɔ flansɛ lamini na. Sigilan yelen ka kan ka kɛ biɲɛ sanuman ye min janya ye milimɛtɛrɛ 2–3 ye.

Supply Line Jɛɲɔgɔnyaw

Nɛgɛ inox sirilenw dilancogo ye sariya ye jagokɛyɔrɔw la k’a sababu kɛ u bɛ se ka pɛrɛn ani u bɛ se ka wuli ka bɔ u nɔ na fɛnɲɛnamafagalanw baara waati:

• Aw bɛ baara kɛ ni layiniw ye minnu jatera ka kɛɲɛ ni a dɔgɔyalenba ye125 PSI yebaara degun ani60 degeregoniyahakɛ.
• Bolo-aw bɛ degunw siri da tugulanw kan, o kɔ aw bɛ tilancɛ-kurun wɛrɛ siri ni fɛn dɔ ye.Aw kana baara kɛ ni pipe dope walima thread tape yekan compression fittings - sigilan bɛ bɔ ferrule la, a tɛ bɔ jiriw la.
• Jɛɲɔgɔnyaw bannen kɔfɛ, aw bɛ da tugu dɔɔni dɔɔni walasa ka ji marto sɔgɔ.

Silicone Seal ka kogo Interface

Ji balilan laban ye silikɔni biɲɛ ye min bɛ jisigiyɔrɔ kɔkanna ni kogo dafalen cɛ:

• K'a nafa bɔ a la100% neutre-silikɔni furakɛli. Acrylic caulk bɛ dɔgɔya ka fara ɲɔgɔn kan kalo 6 kɔnɔ.
• Aw bɛ a kɛ ka taa a fɛ5mm biɲɛkɔfɛla bɛɛ la, jisigiyɔrɔ bɛ kogo kunbɛn yɔrɔ min na.
• Aw bɛ biɲɛ in kɛ ka a nɔgɔya ni bolokɔni ɲiginnen ye walima ni silikɔni sɔgɔlan ye miniti 3 kɔnɔ a kɛli kɔfɛ.
• Ka yamaruyaLɛrɛ 24 kɔnɔfurakɛli waati sani aw ka sigilan bila ji la.

Post-Installation Leak Test Protocol

Sani aw ka a sigili di baarakɛla ŋana ma:

• Aw bɛ jisigiyɔrɔ fa fo ka se a dan na ka a to a ka jɔMiniti 15 kɔnɔ. Aw bɛ jɛgɛnsira bɛɛ lajɛ duguma ni papiye jalen ye - ji suguya o suguya ye dɛsɛ ye.
• Aw bɛ jibolisira bila ka jibolisira lajɛcogo kɔlɔsi a hakɛ dafalen-jibɔ waati. Aw bɛ compression gasket yɔrɔ lajɛ ni ji tɛ a la.
• Aw bɛ ji funteni (60℃) boli kaMiniti 5 kɔnɔani ka segin ka -sɛgɛsɛgɛ fɛnw dilancogo ɲɔgɔndanw bɛɛ la. Sumaya bonya bɛ se ka jɛɲɔgɔnyaw jira minnu tun bɛ dankan na nɛnɛ waati.
• Sɛbɛnni kɛ kɔrɔbɔli la ni ja minnu bɛ don donw na, minnu bɛ tali kɛ ɲɔgɔndan jalenw na, walasa ka poroze dafa sɛbɛnw sɔrɔ.

Installation fili minnu ka teli ka kɛ, olu ka kan ka kɔlɔsi

Foro baara rapɔɔri minnu bɛ jagokɛyɔrɔ ba caman kɔnɔ, olu b’a jira ko ninnu ye filiw ye minnu bɛ kɛ tuma caman na ani minnu musaka ka bon kosɛbɛ:

Kalansen min ye fɛn ye min bɛ sigi senkan

Kogo-jigin kurunbonkarilan sigili ye fasa saba-injiniyɛri baara ye: ka a sɛgɛsɛgɛ ko kogo bɛ se ka doni ta, ka karamɔgɔya sigi ni tigitigi ye, ani ka ɲɔgɔndan yɔrɔ bɛɛ datugu ji ma don a la. Ni fasa kelen-kelen bɛɛ jateminɛna ka ɲɛ, o nɔ bɛ kɛ jagokɛla ka sanuyaso minɛn ye min bɛ baara kɛ k’a sɔrɔ ladonni ma don a laSan 15–20.

Baarakɛlaw minnu bɛ sinkɔrɔkɛminɛnw ɲɛfɔ boon sanfɛla caman kɔnɔ, ankɔri ni kɔkanna protocole nafa ka bon i n’a fɔ karamɔgɔya yɛrɛ. A ɲɛfɔlen don ka ɲɛjagokɛminɛnw jigincogoni nɛgɛdaga min sigilen don ka ɲɛ, o bɛ mɛn ka tɛmɛ boon labɛnni waati kan. Ankɔri minnu b’a minɛ, olu ka kan ka bɛn ni substrat ye. Nivo min b’a bilasira, o ka kan ka jateminɛ. Siginiden minnu b’a lakana, olu ka kan ka tigitigi kɔrɔsilen sɔrɔ a kɛyɔrɔ bɛɛ la.